🎁 New account: buy your first 10 credits, get 10 more free.Avg. 25–45 min turnaround · Files written on your original readCreate free account

Many modern sportbikes and large touring bikes hide two little-known devices that have a big effect on how the engine feels: an exhaust valve in the exhaust system and, on many four-cylinder bikes without full ride-by-wire, secondary throttle valves in the throttle bodies. Both are moved by small electric motors and controlled by the ECU. When they stick, the bike can feel flat, jerky or light up the warning lamp. This guide explains how both systems work, how the ECU controls them and how to diagnose them in the workshop.

Schematic of a motorcycle exhaust valve system with a butterfly valve in the collector, open and close cables, servo motor with position potentiometer and the ECU
Motorcycle exhaust valve: servo, cables and ECU control (original diagram)

Why a motorcycle needs an exhaust valve

A high-revving engine is designed to make peak power near the top of the rev range. The header pipe lengths, collector and valve overlap are chosen to use exhaust pressure waves at high rpm: a low-pressure wave arrives at the exhaust valve during overlap and helps pull burnt gas out and fresh charge in. At lower engine speeds the same waves arrive at the wrong moment. Instead of helping, they can push exhaust gas back toward the cylinder or pull fresh mixture straight out of the exhaust port. The result is a torque dip in the midrange.

An exhaust valve is a simple butterfly placed in the collector or link pipe. By partly closing it at low and medium rpm, the system changes the pressure wave reflections and back pressure so that midrange cylinder filling improves. As rpm rises the valve opens fully so the exhaust can flow freely for peak power. Manufacturers also use the valve to help meet drive-by noise limits.

How the exhaust valve system is built

At key-on, many bikes run a self-test: the servo sweeps the valve open and closed. If the servo cannot reach its end stops in the expected time, or the feedback voltage is out of range, the ECU stores a fault and usually switches on the engine warning lamp.

Secondary throttle valves: two butterflies per cylinder

Big-bore four-cylinder sportbikes use large throttle bodies to flow enough air at high rpm. The downside appears at low rpm. If the rider snaps a cable-operated throttle wide open at 3,000 rpm, the airflow through a huge bore suddenly slows down, fuel preparation suffers and the engine can bog or deliver an abrupt torque hit.

Secondary throttle valves solve this. Each throttle body has two butterflies:

The rider can open the primary valve as fast as they like, but the ECU only opens the secondary valve as far and as fast as engine speed, gear and primary throttle angle allow. Air speed through the throttle body stays higher, the mixture is prepared better, and torque builds smoothly. Some designs also use the secondary valves for idle and cold-start air control, which links closely to our guide on motorcycle idle speed control.

On bikes with full ride-by-wire, the ECU already controls the main throttle valve directly, so a separate secondary valve is usually no longer needed. The same smoothing logic simply moves into the electronic throttle strategy, as described in our ride-by-wire and traction control guide.

Cross-section diagram of a motorcycle throttle body with an ECU-controlled secondary throttle valve upstream of the cable-operated primary throttle valve and the injector
Dual throttle valve body: secondary and primary butterflies (original diagram)

How the ECU controls both valves

Both systems are controlled by maps in the engine ECU. The exhaust valve usually has a target opening table based mainly on engine speed, sometimes adjusted for gear, throttle opening or riding mode. The secondary throttle has an opening limit based on engine speed and primary throttle angle, often with separate tables per gear. Lower gears are typically more restricted.

These tables do not work in isolation. Fuel and ignition maps on a speed-density or alpha-N system are calibrated with the valves in their normal positions, as explained in our motorcycle fuel injection guide. If the valve position changes, the actual airflow changes too, and the mixture moves away from what the calibration expects. That is why a valve stuck half-closed often feels like a fueling problem.

Illustrative charts of exhaust valve opening versus engine speed and secondary throttle opening limit versus engine speed per gear
Typical control logic for exhaust valve and secondary throttles (illustrative) (original diagram)

Common faults and diagnostic steps

  1. Read the fault memory first. Many motorcycles show manufacturer-specific codes, sometimes as two-digit blink codes on the dashboard, for the exhaust valve servo and secondary throttle system. Look up the exact code in the service manual before testing.
  2. Listen to the key-on self-test. No servo sound, a short or a jerky sweep points to a seized valve, binding cables, a faulty servo or a power supply problem.
  3. Check the exhaust valve mechanically. Disconnect the cables and turn the pulley by hand. Carbon and corrosion can seize the spindle, especially on bikes that are used for short trips or left standing.
  4. Inspect and adjust the cables. Stretched, kinked or incorrectly adjusted cables prevent the valve from reaching its end positions. Follow the manufacturer’s adjustment procedure.
  5. Test the feedback sensor. Back-probe the 5 V reference, ground and signal while moving the valve. The signal should change smoothly with no dropouts. Check voltage drop on the reference and ground, as shown in our voltage drop testing guide.
  6. Clean the throttle bodies. Carbon on secondary valves can make them stick. After cleaning or replacing parts, run the manufacturer’s throttle position reset or synchronisation procedure where required.

Unplugging or removing the exhaust valve servo usually just sets a fault and turns on the warning lamp. It does not give the bike a “free-flowing” exhaust, and it can lose the midrange torque the valve was designed to provide.

What this means for ECU calibration

When a bike gets an aftermarket exhaust, the new system may or may not have a valve. A good calibration takes this into account: valve tables, fuel and ignition maps and any related diagnostic settings must match the actual hardware, so the bike runs cleanly and the warning lamp stays off. The secondary throttle tables are also a key part of making a big bike smooth on the throttle in the lower gears. As always, start with a healthy bike with no stored faults and a full original read of the ECU. Our calibration editor guide explains how such tables are found and edited.

Related fault codes (DTCs)

CodeMeaningTypical causes
P0120Throttle/pedal position sensor/switch “A” circuit malfunctionDamaged TPS connector or wiring, worn sensor track, 5 V reference or sensor ground fault
P0122Throttle/pedal position sensor/switch “A” circuit lowSignal shorted to ground, open 5 V reference, failed sensor
P0123Throttle/pedal position sensor/switch “A” circuit highSignal shorted to 5 V or battery voltage, open sensor ground, failed sensor
P0220Throttle/pedal position sensor/switch “B” circuit malfunctionWiring or connector fault on the second position track, failed sensor
P0222Throttle/pedal position sensor/switch “B” circuit lowShort to ground, open reference, failed sensor
P0223Throttle/pedal position sensor/switch “B” circuit highShort to voltage, open sensor ground, failed sensor
P2135Throttle/pedal position sensor/switch “A”/”B” voltage correlationWorn sensor tracks, corroded connector, voltage drop on shared reference or ground
P2100Throttle actuator control motor circuit/openOpen motor circuit, damaged connector, failed throttle motor or ECU driver
P2101Throttle actuator control motor circuit range/performanceSticking or dirty throttle valve, binding linkage, weak motor, low supply voltage
P0638Throttle actuator control range/performance (bank 1)Valve not reaching the commanded position: carbon build-up, mechanical binding, motor or wiring fault

These are generic OBD-II codes used by many modern ride-by-wire and Euro 5 motorcycles for throttle sensors and throttle actuators. Exhaust valve servo and secondary throttle faults are often reported with manufacturer-specific codes, so always confirm with the service manual for the exact model.

Tuning a sportbike, naked or touring bike? Get professionally developed motorcycle, car, truck and agricultural ECU files at ecufilemarket.com.

Leave a Reply

Your email address will not be published. Required fields are marked *

⚡ New Free Workshop Resource: Hybrid & EV Powertrain Engineering & ECU Diagnostics Training (8 Free PDF Manuals) →