8 Engineering Modules + Complete A4 Master Manual
Instant Direct Google Drive PDF Download (No Signup Wall)
Free Hybrid & Electric Vehicle Powertrain Engineering & ECU Diagnostics Training
Transitioning your workshop from conventional TDI/TSI engines into High-Voltage Hybrid & EV systems requires methodical diagnostic engineering—not guesswork. Prepared by the powertrain calibration team at ECU File Market, ECUFlashFiles & Clean Look Tuning, this free 8-module technical curriculum teaches technicians how to safely isolate 201.6V–500V inverters, interpret MG1/MG2 live data, diagnose BMS block-voltage faults (P3000 / P3006 / P0AA6), and service hybrid engines, regenerative brakes, and multiplex networks.
Single printable A4 engineering manual · Vector diagrams, freeze-frame benchmarks, SMR contactor logic & diagnostic checklists (459 KB PDF)
Download Individual Hybrid & EV Engineering Modules (Direct PDF)
Click Direct Download PDF on any module below for immediate one-click download straight from Google Drive—zero email gates, ready to print for your diagnostic bench.
151 KB PDF
Hybrid Powertrain Architecture, MG1/MG2 & Power-Split Mechanics
Series-Parallel THS vs 500V Boosted THS-II (P111 vs P112), 78/23/30T Planetary Gear Collinear Nomographs, Reverse & B-Mode physics, 6 Operating Modes, and Smart Key READY state logic.
101 KB PDF
High-Voltage Safety Protocol, 500V Boost Inverter, Resolvers & Cooling
Class-0 1,000V Glove air-leak inspection, 6-step HV de-energizing & mandatory 5-minute capacitor 0V verification, IGBT/IPM Boost Converter, 12V DC-DC, Rotor Resolvers & HVIL/INF codes.
126 KB PDF
HV Battery Pack, BMS SOC Logic, SMR Pre-Charge & P3000/P3006 Diagnosis
Prismatic Ni-MH 201.6V/273.6V module math, 60% target SOC window, SMR1/SMR2/SMR3 contactor sequence, real P3000 (INF 123) & P3006 block-voltage freeze frame, P3076 airflow & 12V AGM rules.
104 KB PDF
Atkinson 1NZ-FXE ICE, Coolant Heat Storage, Bladder Tank & 3-VSV EVAP
Late intake valve closing (72°–105° ABDC) compression testing, Planar 3.3V A/F sensor, 3-day Thermos coolant tank active bleeding, resin bladder fuel tank reset & P0440–P1455 EVAP testing.
128 KB PDF
Shift-by-Wire, 61:1 Parking Actuator, ECB Regenerative Brakes & EPS
Dual Hall-IC shift sensors, cycloid parking pawl actuator, Electronically Controlled Braking (ECB) MG2 torque blending, 28-capacitor backup unit, C1215/C1259 & EPS C1515 zero-point calibration.
113 KB PDF
201.6V ES18 Electric A/C, ND-OIL 11 Isolation Law & CAN/BEAN Multiplex
Brushless HV electric scroll compressor diagnosis, why 1% PAG oil triggers P3009/P0AA6 HV isolation shutdown, Sub-Cool condenser weigh-in rule, PTC heaters & 500k CAN / BEAN / AVC-LAN Gateway.
124 KB PDF
Live Data Sign Matrix (Motor vs Generator), Benchmarks & History Counters
Instant MG1/MG2 RPM × Torque sign law (+/+ vs +/-), snapshot walkthroughs (Stationary, WOT, Regen, Reverse, B-Mode), HV ECU Operation History forensics (AUX BATT LOW, INV TEMP) & full Data List.
104 KB PDF
Hybrid & EV Workshop SOPs, Neutral Drain Law, 3-Loop Bleed & Glossary
Printable shop wall rules: why Neutral in READY drains HV packs beyond cranking threshold, flatbed towing law, <60°C paint booth rule, 3-circuit coolant purge checklist & A–Z hybrid glossary.
Quick Workshop Reference #1: MG1 & MG2 Live Data Speed × Torque Sign Law
When inspecting Hybrid ECU Live Data (MG1 REV, MG1 TORQ, MG2 REV, MG2 TORQ), apply mechanical power physics P = (ω × T): identical algebraic signs mean the machine is operating as a Motor (consuming HV power); opposite algebraic signs mean it is operating as a 3-Phase Generator (regenerating/charging).
| Driving Condition | MG1 Speed / Torque | MG1 Mode | MG2 Speed / Torque | MG2 Mode |
|---|---|---|---|---|
| Stationary HV Charging in P | +3,380 RPM / -28 Nm | Generator (Charging Pack) | 0 RPM / 0 Nm | Stationary |
| WOT Acceleration (500V Boost) | +4,500 RPM / -38 Nm | Generator (Feeding MG2 Bus) | +2,400 RPM / +190 Nm | Traction Motor (+/+) |
| Regenerative Coasting / Braking | -950 RPM / 0 Nm | Freewheeling | +1,450 RPM / -115 Nm | Regen Generator (+/-) |
| Reverse Gear (EV Drive) | +620 RPM / 0 Nm | Freewheeling | -420 RPM / -85 Nm | Reverse Motor (-/-) |
| Steep Downhill in “B” Range | +2,600 RPM / +18 Nm | Motor (Spins Unfueled ICE) | +2,100 RPM / -75 Nm | Regen Generator (+/-) |
Quick Workshop Reference #2: SMR Contactor Pre-Charge & DTC P3000 / P3006 Freeze-Frame Benchmarks
System Main Relay (SMR1 / SMR2 / SMR3) Sequence
- Step 1 (Pre-Charge):
SMR1 (Positive Pre-charge + 20Ω Resistor)andSMR3 (Negative Main)close first so Inverter smoothing capacitors charge smoothly toVL ≈ 201.6Vwithout welding contacts. - Step 2 (Main Bus Lock):
SMR2 (Positive Main)closes across zero voltage differential;SMR1then opens andREADYilluminates. - Step 3 (Shutdown Weld Verification): HV ECU staggers
SMR2andSMR3opening while monitoringVLcapacitor bleed-down to detect stuck contactors (P0AA1 / P0AA4).
Critical HV Diagnostic Thresholds
- Target SOC Window:
60%nominal (40%–80%operating swing;DELTA SOC > 20%setsP3006). - Shorted Cell Detection: Compare all 14 monitored 14.4V module-pairs under +80A WOT load and -50A regen braking—any block diverging >1.2V (e.g.,
9.92Vvs15.5V) confirms internal cell failure. - HV Ground Isolation & Electric A/C Rule:
SHORT WAVE HIGH ≥ 4.0Vindicates active HV leakage (P3009 / P0AA6). Strictly use ND-OIL 11 (POE) in 201.6V electric A/C compressors—even 1% PAG oil causes HV isolation failure!
Hybrid & Electric Powertrain Diagnostic FAQ
Why should a hybrid vehicle NEVER be left in Neutral (N) with READY mode ON in the workshop?
In N, the HV ECU shuts off all Inverter IGBT gate signals to guarantee zero transaxle reaction torque. Because MG1 is electrically disabled in Neutral, the engine CANNOT crank or charge the HV traction battery—even if the ICE is already idling! Leaving the car in N with A/C or 12V loads active drains the HV pack below starter threshold.
What is the mandatory high-voltage de-energizing wait time after pulling the orange HV Service Plug?
After switching POWER OFF, moving the Smart Key >5 meters away, disconnecting the 12V negative terminal, and removing the orange Service Plug while wearing Class-0 (1,000V air-tested) insulated gloves, you MUST wait a minimum of 5 full minutes for internal Inverter smoothing capacitors to bleed down, followed by a 0.0V DC verification across Inverter HV terminals using a CAT III 1,000V DVOM.
Why does Skid Control DTC C1259 appear together with Engine or Hybrid ECU faults?
DTC C1259 (HV System Regenerative Malfunction) is an informational companion code logged by the Electronically Controlled Brake (ECB) ECU whenever the HV ECU suspends MG2 regenerative braking due to an upstream HV battery, inverter, or engine fault. Always diagnose and repair the HV ECU / ECM / Battery ECU root-cause DTCs (plus their 3-digit INF sub-codes) first.
Does ECU File Market support Hybrid & Electric/PHEV ECU calibrations and OEM stock files?
Yes! ECU File Market supplies verified OEM stock files, Stage 1 petrol-hybrid torque calibrations (Bosch MED17, MG1CS, Continental Simos, Denso Atkinson/Turbo-Hybrid ECUs), DTC diagnostics, EVAP/EGR engineering for motorsport/off-road applications, and bench/boot pinout guidance for professional workshops worldwide.
Servicing Petrol-Hybrid, Mild-Hybrid (48V), PHEV or Diesel ECUs in Your Workshop?
Join independent workshops across Europe using ECU File Market for custom dyno-verified calibrations, OEM stock recovery binaries, and 25–45 minute engineering turnaround.