A WinOLS project starts as a block of raw numbers. Before anything can be changed, the maps inside that file have to be found and identified. This guide shows how to find maps in WinOLS: the automatic background map search and the “potential maps” it produces, how to review them, and how to find and define a map by hand in Text and 2D mode. It is based only on EVC’s public WinOLS 5.94 manual and EVC’s FAQ pages, linked in the sources at the end.
Facts checked on 2 November 2026 in the WinOLS 5.94 manual (English PDF) and the EVC FAQ. Shortcuts and menu names can change between WinOLS versions, and the manual and the FAQ differ in a few details, which are noted below. If you have not created a project yet, start with our guide to importing an original read into WinOLS. For what maps are, see our ECU maps explainer.

Step 1: let WinOLS search automatically
When you create a new project and import a file, WinOLS starts a background search for maps after a few seconds. You can see it running in the status bar at the bottom of the window, and you can influence it through the map search menu items (source, source). Two details help results:
- Fill in the “producer” field. In the lower-left project fields, “producer” is important for the automatic map search. An incorrect or empty value can reduce the number of maps found, because WinOLS uses producer-specific algorithms (source).
- The search runs once. According to the manual, potential maps are searched only once: if you save the project and reopen it, they are not searched again. The manual’s command reference also lists a command to start, stop or restart the background map search (source).
Step 2: review the “potential maps”
- Open the folder. A new sub-folder labelled “potential maps” appears in the project and map list on the left. Open it by clicking it. It contains every map found during the search (source, source).
- Click an entry to see it. Selecting a map in the folder shows it in the hexdump. If the Preview window is open (hotkey P), you get a 3D preview of the potential map straight away (source).
- Step through the results. Use View > Recognize map (hotkey F) to jump to the next map and select it; Shift+F goes to the previous one (source).
- Use the tags. Every automatically recognised map has a small tag with its name in the hexdump. Click the tag to display the map optimally, double-click it to convert the potential map into a normal map that is easier to edit, and right-click it for more options (source).
Potential maps are marked with a border and a tag on top, while registered maps are shown with a coloured background. Both can be switched on or off in the view settings (source). If you do not want a potential map, the manual lists a context-menu command to remove it (source).
Tuning the map search
The map search dialog (Miscellaneous > Configuration > Automatically > Map search) controls how maps are searched, both for the direct search (F) and the background search. To reduce false detections, WinOLS ignores several map types by default, for example maps consisting of only one value or of two alternating values, and you can choose to accept them. The dialog can also search in vendor-specific formats and offers a “statistical map recognition” that judges data by its look, which finds maps without headers or structure data but takes much longer and rarely recognises axis data (source). Our overview of how files are organised is in what a calibration editor does.
Step 3: finding a map by hand (Text mode)
EVC is clear that finding maps manually is not easy and needs skill. The manual’s text-mode procedure is (source, source):
- Choose a view mode. Use the tabs Text, 2d and 3d at the bottom of the window, or the hotkeys T and Shift+T. (The FAQ page prints “Shift+F” here, but the current manual says Shift+T, and F is the Recognize map hotkey.)
- Choose the view parameters. Double-click the window and set the values (8 bit, 16 bit and so on). New ECUs often use 16-bit data. Motorola processors use HiLo notation and Intel processors use LoHi; WinOLS recognises the processor manufacturer automatically, and you can see it under Project > Properties: Project.
- Scroll through the file with the mouse wheel, scroll bar or keys. Pale numbers mean WinOLS recognised the area as program code: ignore it, since maps are normally not there and changes could crash the vehicle’s software. Empty areas are also uninteresting. The overview window (Window > Overview) gives a rough outline of the project.
- Set the number of columns. When you find something that could be a map, adjust the view first. Maps often show “jumps” that represent a new line; change the number of columns until the jumps are all in the same columns, with the hotkeys M and W, or by dragging the single vertical line in Text mode.
- Move the origin. Make the map start at the left of the hexdump with View > Move origin left / right (Ctrl + cursor left or right).
- Select the map. If the bar display shows little, select the map and use View > Optimize value range (Ctrl+B) so the bars use the available height. With the Preview window open you see a 3D preview of the selection.
- Create the map. Use Selection > Selection -> Map (hotkey K). A new window opens and you can edit the map.

Finding a map in 2D mode
The 2D procedure is similar: set the view parameters, scroll to a candidate, then set the columns so that the vertical lines (which mark the line breaks in 2D mode) run parallel to the “jumps” in the data, and move the origin as above. Selecting is fiddlier because the pixels are close together. Mark the map roughly, then move the cursor over the left end of the selection until it becomes an arrow pointing to a line, and drag to adjust. WinOLS makes sure the selection starts on a line break; repeat on the right end (source, source). X and Y zoom can be changed to make this easier.
Let WinOLS help with the selection
- Support map selection. View > Support map selection tries to optimise your selection by performing the steps above (columns, start and so on) automatically. Applied to an existing selection it works once; activated, it applies to every new selection. Be careful not to select data that does not belong to the map (source).
- Map selection symbol bar. Activate View > Symbol bars > Frame: Map Selection to change the start in X or Y direction or the number of rows and columns after you draw a rectangular selection (source).
- Context menu. In both modes, right-clicking in a selection gives the same functions (source).
Practical advice
- Work in a version. The Original is the reference for comparison; change only versions. See our guide to comparing files and importing changes.
- Treat names as leads. A tag gives a suggested name. Confirm with the axes, the units and the shape of the data, and with a datalog where possible.
- Do not edit program code. Pale areas are not for editing.
- Save and reuse. Once maps are defined, the same structure can be reused on similar files with map packs and scripts.
- Checksums. After changes, checksums must be handled before export; see checksum correction with plugins.
Common problems
- Few or no potential maps. Check the “producer” field (source), make sure the project holds the complete read, and restart the map search from its menu command (source).
- A found map looks wrong. Re-check 8 or 16 bit, HiLo or LoHi (the manual ties byte order to the processor type) and the number of columns (source).
- The map selection keeps shifting. Move the origin until the first value sits at the left, then re-select with Support map selection.
Need the file done for you?
If you would rather not map and edit a file yourself, upload your original read to ECU File Market with the vehicle, ECU hardware and software numbers and the tool you used. Credit prices are on our pricing page, and most files are returned in under one hour during support hours.
Good practice: only work on vehicles you own or are authorised to work on, keep the original file for the life of the car, and keep all emission control systems fitted and working. This guide does not cover removing or disabling DPF, EGR, SCR/AdBlue or any other emission equipment.
Sources (checked 2 November 2026)
- EVC WinOLS 5.94 manual (English PDF), chapters 2.2 to 2.4 Automatically / manually find maps (Text and 2d mode), project fields, view settings, Configuration / Automatically / Map search: evc.de/ftp/winols/WinOLS HelpEn.pdf
- EVC FAQ, “How can I automatically find maps?”: evc.de/en/service/q1601.asp
- EVC FAQ, “How can I manually find maps (Text mode)?”: evc.de/en/service/q1602.asp
- EVC FAQ, “How can I manually find maps (2d mode)?”: evc.de/en/service/q1603.asp
WinOLS is a registered trademark of EVC electronic GmbH. ECU File Market is an independent tuning file service and is not affiliated with, endorsed by or sponsored by EVC. The name is used only to describe compatibility and workflow. Use only genuine, licensed software.