Most modern diesel and many petrol cars with a manual or dual-clutch gearbox do not have a simple one-piece flywheel. They use a dual-mass flywheel (DMF): two heavy discs joined by springs. It is one of the parts that makes a modern high-torque engine feel smooth at low rpm, and it is also one of the parts that suffers most when torque goes up. This guide explains how a DMF works, how it fails, how to diagnose it and why it matters for calibration work.

Why engines need torsional damping
A piston engine does not deliver torque evenly. Each firing stroke gives the crankshaft a push, and between strokes it slows slightly. The result is a small speed fluctuation on every revolution, called torsional vibration. It is strongest at low rpm, with few cylinders and with high cylinder pressure, which is exactly how a modern turbo diesel is driven.
If those pulses reach the gearbox, loose gears hammer against each other (gear rattle), the body booms and the driver has to keep the engine speed higher than it needs to be. Older cars handled this with a single-mass flywheel and a clutch disc that had small coil springs in its hub. As torque rose and engines were tuned to run at lower speeds, those springs no longer had enough travel. The DMF moves the damping into the flywheel, where there is room for much longer springs.
How a dual-mass flywheel is built
A typical DMF has four main parts:
- Primary mass: bolted to the crankshaft and usually carrying the starter ring gear. It turns exactly with the engine.
- Secondary mass: the clutch pressure plate bolts to this side and the clutch disc runs against it. It turns with the gearbox input when the clutch is engaged.
- Arc springs (also called bow springs): long curved springs sitting in a grease-filled channel between the two masses. They compress and extend with every firing pulse.
- Bearing and friction control: a central bearing lets the masses rotate relative to each other through a limited angle, and friction elements control how quickly they swing.
Some designs add an inner damper stage, a centrifugal pendulum absorber or a planetary gear set to tune the response at different speeds. Because the DMF does most of the damping, the clutch disc used with it is often a rigid disc with no hub springs.
What the DMF actually does
The primary mass follows the uneven crankshaft speed. The springs absorb most of that fluctuation, so the secondary mass and the gearbox see a much smoother speed. The system is tuned so that its natural resonance sits below idle speed. That is why engines with a DMF pass through a short shake when starting and stopping, and why they idle more smoothly once running.

How DMFs wear and fail
A DMF is a wear part. The springs and their channel wear, the grease can dry out or leak, and the bearing develops play. Heat from a slipping clutch speeds all of this up. Wear is worse with:
- Lugging the engine at very low rpm in a high gear
- Frequent hard launches and aggressive clutch use
- Repeated stalling and rough starts, which drive the masses through resonance harder
- Torque well above what the flywheel and clutch were designed for
Typical symptoms are a rattle or knock at idle (often heard best when starting or switching off), judder when pulling away, a clunk when going on and off the throttle, and vibration through the pedal or floor at low rpm.
Diagnosing a suspected DMF
Many DMF symptoms look like other faults, so rule out the cheaper causes first.
- Check engine running quality. Read misfire counters and, on diesels, cylinder balance or injector correction values. An uneven engine can feel like a bad flywheel. Our guide to misfire detection explains how the ECU measures this from crankshaft speed.
- Inspect engine and gearbox mounts and driveshaft joints. Worn mounts cause judder and clunks too.
- Listen with the clutch pressed and released. A change in noise points to the clutch and flywheel area, although a release bearing can also do this.
- Measure free angle and rock with the gearbox removed, using the manufacturer’s tool and published limits. Free angle is how far the secondary mass turns against the primary before the springs load up. Rock is how much the secondary mass tilts. Guessing by hand is not reliable.
- Inspect the clutch at the same time. Heat marks, oil contamination or a glazed disc often explain the symptoms, and it is usually best practice to replace clutch and DMF together.
A DMF has no sensor of its own, so it does not set a fault code directly. The codes below are the ones you may see around the same complaint, especially crankshaft signal and clutch codes.

Single-mass conversion kits
Kits that replace the DMF with a solid flywheel and a sprung clutch disc are sold for many models. They are cheaper and handle heat well, but the original damping is gone. Expect more gear rattle, more vibration at low rpm and more load on the gearbox and engine mounts. Whether that is acceptable depends on the car and how it is used.
What tuning means for the DMF and clutch
Every DMF and clutch has a torque capacity. Raising torque, especially low-rpm torque on a diesel, loads the springs harder and moves the clutch closer to slipping. A sensible calibration takes this into account:
- Shape the torque build-up so peak torque does not arrive suddenly at very low rpm.
- Use gear-based and speed-based torque limits where the original software has them. Our article on ECU limiters and the torque model explain how these fit together.
- On automatics and dual-clutch gearboxes, the TCU has its own torque limits. See our dual-clutch transmission guide.
- Check the flywheel and clutch condition before tuning. A worn DMF will not get better with more torque.
As with any ECU work, start from a complete, verified original read. Our guide to ECU reading methods covers the options.
Related fault codes (DTCs)
These are generic SAE definitions. Manufacturers may use their own codes or wording, so always confirm the definition for the specific vehicle.
| Code | Meaning | Typical causes |
|---|---|---|
| P0300 | Random/Multiple Cylinder Misfire Detected | Ignition or injection faults, low compression, air leaks; rough driveline behaviour from a worn DMF can make a misfire complaint harder to pin down |
| P0335 | Crankshaft Position Sensor A Circuit | Sensor failure, damaged wiring or connector, poor ground, sensor-to-trigger-wheel gap problems |
| P0336 | Crankshaft Position Sensor A Circuit Range/Performance | Damaged, loose or dirty trigger wheel, wrong air gap, signal interference, intermittent wiring |
| P0016 | Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A) | Stretched timing chain or belt jumped a tooth, VVT faults, trigger wheel slipped or damaged |
| P0811 | Excessive Clutch A Slippage | Worn or contaminated clutch, weak pressure plate, hydraulic release fault, torque above clutch capacity |
| P0830 | Clutch Pedal Switch A Circuit | Faulty or misadjusted switch, wiring or connector fault |
| P0831 | Clutch Pedal Switch A Circuit Low | Short to ground, failed switch, damaged wiring |
| P0832 | Clutch Pedal Switch A Circuit High | Open circuit, short to voltage, failed switch |
| P0833 | Clutch Pedal Switch B Circuit | Faulty or misadjusted second switch, wiring fault, plausibility error between switches |
Planning a tune on a car with a dual-mass flywheel? Upload your original ECU read at ecufilemarket.com and get a custom tuning file prepared for your vehicle and its hardware.