🟢 Calibrators Online · Avg. Delivery: 25–45 min
6 Credits Standalone · +2 Cr Add-on with Stage 1/2
DPF / FAP / OPF / GPF Off File Service for Workshops
ECU File Market provides custom DPF (Diesel Particulate Filter), FAP, and OPF/GPF deactivation calibrations written directly on your original ECU read. Unlike generic automated switches that break cruise control or leave dash regeneration loops active, our engineers calibrate the complete soot/ash model, post-injection maps, and differential pressure monitoring. Cost: 6 Credits standalone (€48 in the 10-credit workshop pack, or €24 effective with the 10+10 welcome bonus) or +2 Credits (€16) when combined as an add-on with Stage 1 or Stage 2. Average delivery: 25–45 minutes.
🔍 Free Instant ECU Binary & % OEM Originality Scanner
.bin / .ori / .mpc / .fls file below to instantly check its Bosch/OEM SW number, % OEM originality, and exact per-ECU credit price before registering!Technical Compatibility Matrix (ECUs, Read Modes & Tools)
Every calibration is engineered directly on the original binary dump you read from the vehicle. Below is the hardware and protocol matrix for workshop tools:
| ECU Family | MCU / Platform | Read Method | Compatible Tools | Sensor / Disconnect Protocol | Credit Cost |
|---|---|---|---|---|---|
| Bosch EDC16 (C31, C34, C39, CP33, CP34, U31) | MPC555 / MPC562 | OBD / BDM / Bench | KESS3, Autotuner, Flex, MPPS, FoxFlash | Emulation switch + post-injection off; sensors stay connected on most SW | 6 Cr Solo (+2 Cr w/ Stage 1) |
| Bosch EDC17 (C46, C50, C56, C64, C74, CP14, CP44, CP54) | Infineon Tricore TC1767 / TC1797 / TC1793 | Bench / OBD VR / Boot | Autotuner, Flex, KESS3, DFOX, PCMFlash | Full soot model & regen switch off; diff. pressure & EGT sensors can stay connected | 6 Cr Solo (+2 Cr w/ Stage 1) |
| Bosch MD1 (MD1CS001, MD1CS004, MD1CS006, MD1CP002) | Aurix TC298TP / TC299TP | Bench / Unlock | Autotuner, Flex, KESS3, DFOX, CMD, bFlash | Complete DPF + regen inhibit in Flash; reset ash counter before writing | 6 Cr Solo (+2 Cr w/ Stage 1) |
| Bosch MG1 / MED17 (OPF / GPF Petrol Particulate Filter) | TC1793 / Aurix TC277TP / TC298TP | Bench / OBD VR | Autotuner, Flex, KESS3, PCMFlash, BitBox | OPF/GPF differential pressure monitoring & regen mode disabled without torque limp | 6 Cr Solo (+3 Cr w/ Stage 1) |
| Continental PCR2.1 / SID208 / SID307 / SID309 / SID310 | Tricore TC1796 / TC1797 / TC1791 | Bench / OBD (PCR2.1 unlock) | Autotuner, Flex, KESS3, DFOX, PCMFlash | On Renault/Nissan SID309/310 & Delphi DCM6.2, reset DPF ash mass via diagnostic tool prior to flash | 6 Cr Solo (+2 Cr w/ Stage 1) |
| Delphi DCM3.5 / DCM6.2A / DCM6.2V / DCM7.1A/B | NXP / Tricore TC277 / TC297 | Bench / Boot / OBD | Autotuner, Flex, KESS3, DFOX, CMD | Full regeneration state-machine disable + related P2002 / P2463 / P2452 DTC table cleanup | 6 Cr Solo (+2 Cr w/ Stage 1) |
| Heavy-Duty Truck & Agri (EDC17CV41/42, EMS2.4, MCM2.1, S8) | Tricore / Freescale HD | Bench / Boot / OBD | KESS3 Truck, DFOX, Autotuner, Flex, PCMFlash | Combined DPF + SCR/AdBlue torque derate removal for Euro 6 trucks & Stage IV/V tractors | 6 Cr Solo (+2 Cr w/ Stage 1) |
🛠️ Workshop Diagnostic Protocol (Before & After Writing)
- 1. Reset DPF Soot / Ash Mass Before Writing: Always run the ‘DPF Replacement / Reset Ash Counter’ adaptation with your diagnostic scan tool (VCDS, ODIS, ISTA, Diagbox, Clip, Launch, Autel) on the stock file before flashing the modified file.
- 2. Mechanical Filter Removal: Once the DPF/FAP calibration is flashed, the physical ceramic core must be removed or replaced with a test pipe so exhaust backpressure does not damage the turbocharger.
- 3. Differential Pressure & EGT Sensors: On Bosch EDC17/MD1 solutions, differential pressure and exhaust gas temperature sensors can remain plugged in. If a sensor is physically broken/shorted, list its fault code (e.g.
P2454,P0546) in the upload notes so we disable the sensor supply check. - 4. Oil Dilution Reset: On Mazda Denso, Ford SID208, and PSA DCM6.2/MD1CS003, reset the engine oil service/dilution counter via diagnostics after flashing.
💳 Transparent B2B Credit Pricing
Order DPF/FAP Off as a standalone job (Solutions Only) for 6 Credits (€48 in 10-pack), or combine it with a Stage 1 / Stage 2 remap for only +2 extra Credits (€16)!
- 1 Credit Single Top-up: €10 (€10.00 / credit)
- 10-Credit Workshop Pack: €80 (€8.00 / credit)
- 🎁 New Account Welcome Bonus: Buy your first 10 credits (€80) and get +10 extra credits FREE (20 credits total = €4.00 / credit effective cost!)
- 100-Credit Pro Volume Pack: €600 (€6.00 / credit)
Start Upload / Create Free Account →
Need a virgin / stock OEM file because the ECU on your bench was already modified? Search by Bosch/OEM SW number on our sister database ecuflashfiles.com or request it in your upload notes.
Frequently Asked Workshop Questions
How much does a DPF / FAP Off file cost in credits?
A standalone DPF / FAP Off file costs 6 credits (€48 at the 10-credit workshop pack rate, or €24 effective with the 10+10 welcome bonus). When combined with a Stage 1 or Stage 2 remap, DPF Off is discounted to only +2 extra credits (€16).
Do I need to disconnect the differential pressure or temperature sensors?
On most Bosch EDC16, EDC17, and MD1 ECUs, our complete emulation solution allows you to leave all sensors plugged in. If a sensor is already faulty or damaged, simply write the DTC code in the upload notes and we will unmap that sensor channel completely.
Why must I reset DPF ash load before flashing on Renault SID309/310 and PSA DCM6.2?
Continental SID309/310 and Delphi DCM6.2 store the accumulated soot/ash counter in EEPROM. Resetting DPF replacement in diagnostics before flashing ensures the EEPROM status flag is cleared so the dashboard never shows a ‘Check Anti-Pollution System’ message.
Is this calibration intended for motorsport / export / off-road use?
Yes. Removing or deactivating emissions hardware affects road-legal compliance in many jurisdictions. Workshops order and install these files for motorsport, track, agricultural, export, or off-road machinery under their own responsibility.