A fault code tells you a monitor has already failed. By then the customer has a warning light and you are working backwards. OBD-II Mode $06 (Service $06, “on-board monitoring test results”) lets you see the actual numbers the ECU measured during its self-tests, and how close each one is to its pass/fail limit. Used well, it shows a weak catalyst, a lazy oxygen sensor or a cylinder that is starting to misfire before a DTC is stored. This article explains how Mode $06 works, how to read it and where it fits in a diagnosis.

Continuous and non-continuous monitors
The OBD system checks emission-related parts in two ways. Continuous monitors (misfire, fuel system and comprehensive components) run all the time while the engine is running. Non-continuous monitors run once per trip, only when their enable conditions are met: engine temperature, load, speed, time since start, fuel level and so on. Examples are the catalyst, oxygen sensor, oxygen sensor heater, EGR, EVAP, secondary air and VVT monitors. The readiness monitors article explains how these tests are scheduled.
Every time a non-continuous test runs, the ECU stores the result. Readiness status only tells you “complete” or “not complete”. Mode $06 gives you the measured value behind that status.
What a Mode $06 result contains
On CAN vehicles, each result is organised by:
- OBDMID (monitor ID): which monitor the test belongs to, for example $01 for the oxygen sensor monitor bank 1 sensor 1, $21 for the catalyst monitor bank 1, $31 for the EGR monitor bank 1 or $A2 for misfire data on cylinder 1.
- TID (test ID): which test inside that monitor. One monitor can run several tests, such as a sensor switching time and a voltage amplitude.
- Unit and scaling ID: tells the scan tool how to turn the raw number into volts, milliseconds, a ratio, a percentage or counts.
- Test value, minimum limit and maximum limit: the value passes when it is inside the limits.
The monitor ID ranges are standardised, but many test IDs inside them are defined by the vehicle maker. A good scan tool translates the common ones. For the rest you need the manufacturer’s Mode $06 tables. Older pre-CAN vehicles used a different structure with mostly manufacturer-specific test IDs, so the values are harder to interpret without service data.

Why marginal passes matter
A pass is not the full story. If the catalyst test value is just inside its limit, the next cold morning or longer trip may push it over. If one cylinder shows misfire counts in Mode $06 while the others show zero, it may have a coil, plug or injector that is starting to fail. Because a misfire DTC needs a certain rate over a set number of revolutions, low-level misfires can exist for a while without any code.
Typical things technicians check in Mode $06:
- Per-cylinder misfire counts (OBDMID $A2 onwards on many CAN vehicles), often shown for the current or last drive cycle and as an averaged value. Compare all cylinders.
- Catalyst monitor results as a value against a threshold. Read this together with the catalyst monitor and P0420 explanation.
- Oxygen sensor tests such as response or switching time and voltage range. A slow sensor can affect fuel control and the catalyst test. See how lambda sensors work.
- EVAP leak test results for the different leak sizes, and purge flow results.
- EGR flow tests, where supported.
How to use Mode $06 in a diagnosis
- Read stored and pending DTCs, freeze frame data and readiness status first.
- Check that the monitor you care about has completed on this drive cycle. If it has not, the Mode $06 values may be old or default numbers.
- Read Mode $06 and note the value, minimum and maximum for each relevant test.
- Look for values close to a limit and compare banks or cylinders against each other.
- Confirm with live data, fuel trims, a scope and component tests. Mode $06 points you in a direction. It does not replace testing.
- After the repair, complete a drive cycle that runs the monitor and check that the value has moved away from the limit. This is a strong way to prove the repair worked.

Limits and common pitfalls
- Values reset when codes are cleared or the battery is disconnected on many vehicles, so read Mode $06 before clearing anything.
- Some tools show raw hex values without scaling. Use a tool that applies the unit and scaling ID, or convert using the maker’s tables.
- Limits come from the manufacturer’s calibration. Do not compare values between different vehicles or engines.
- Diesel cars and newer vehicles may report different monitors, such as NOx and particulate filter related tests, and support varies a lot.
- Heavy-duty engines using SAE J1939 have their own diagnostic messages for test results, so a light-vehicle Mode $06 tool may not show them.
Why it matters for tuning
Monitors and their thresholds are part of the ECU calibration. A well-built tuning file keeps emission monitors working as the manufacturer intended, so Mode $06 results stay meaningful after a remap. If misfire counts or oxygen sensor results change after tuning, treat it as a fault to investigate, not as normal behaviour.
Related fault codes (DTCs)
These are common generic OBD-II codes whose monitors also report test results in Mode $06. Wording can vary slightly between makes, so confirm with service data.
| Code | Meaning | Typical causes |
|---|---|---|
| P0300 | Random/multiple cylinder misfire detected | Ignition faults, vacuum leaks, low fuel pressure, injector problems, low compression |
| P0301 | Cylinder 1 misfire detected | Coil or spark plug, injector, valve or compression problem on cylinder 1 (P0302–P0306 follow the same pattern for cylinders 2–6) |
| P0420 | Catalyst system efficiency below threshold (bank 1) | Worn or poisoned catalyst, exhaust leak before the rear sensor, slow or faulty oxygen sensor, misfire history |
| P0430 | Catalyst system efficiency below threshold (bank 2) | Same causes as P0420 on bank 2 |
| P0133 | O2 sensor circuit slow response (bank 1 sensor 1) | Aged or contaminated sensor, exhaust leak, wiring fault |
| P0135 | O2 sensor heater circuit malfunction (bank 1 sensor 1) | Failed heater element, blown fuse, open wiring, ECU driver fault |
| P0171 | System too lean (bank 1) | Vacuum or intake leaks, MAF error, low fuel pressure, restricted injectors |
| P0401 | Exhaust gas recirculation flow insufficient detected | Carbon-clogged EGR valve or passages, failed valve, sensor or hose faults |
| P0441 | Evaporative emission system incorrect purge flow | Purge valve stuck or not opening, blocked or disconnected purge lines |
| P0442 | Evaporative emission system leak detected (small leak) | Loose or worn fuel cap seal, cracked EVAP hoses, leaking canister or vent valve |
| P0455 | Evaporative emission system leak detected (large leak) | Missing or open fuel cap, disconnected hose, failed vent or purge valve |
| P0456 | Evaporative emission system leak detected (very small leak) | Small hose cracks, filler neck seal, cap seal, canister seams |
Need a tuning file that keeps every OBD monitor working? Upload your original ECU read to the tuning file service at ECUFileMarket for a file built for your exact hardware and software.