A remap is only half the job. The other half is checking how the engine actually responds to the new file, and that is what datalogging is for. This guide shows how to datalog with AutoTuner after a remap: what you need, the exact recording routine AutoTuner recommends, how to make a clean pull, and how to share the log with the person who made your file. Everything about the tool comes from AutoTuner’s own public help centre and flash-method pages.
Facts checked on 30 October 2026 in AutoTuner’s public help article on datalogging and its datalogs flash-method page, linked in the sources at the end. Menus and available measures change with software updates and differ per ECU, so always follow what the AutoTuner software shows for your vehicle.

What AutoTuner datalogging records
AutoTuner describes its datalogging as collecting and recording, live, the data sent by the car’s ECU through the OBD socket. For each supported ECU, AutoTuner has pre-selected a set of relevant measures from the manufacturer-specific datalogging parameters, for example boost pressure, load, torque, air/fuel and exhaust gas temperature (source, source). Which measures you actually get depends on the ECU: AutoTuner’s datalogs compatibility list on the flash-method page shows the vehicles where the Datalogs method is offered (source). We do not publish our own list of loggable ECUs, because it changes with AutoTuner’s updates.
In AutoTuner’s own words, tuning without datalogging is like cooking a meal blindfolded: the person tuning needs precise feedback on how the engine reacts to the updated parameters (source).
Before you log: what you need
- The tuned file is written and the car checks out. The engine starts, idles normally and there are no new fault codes. If you have not written the file yet, our AutoTuner OBD read and write guide covers that part.
- Internet on the laptop. AutoTuner says the computer must be online, but only to query the available measures from the server and to upload the log when recording is finished. Wi-Fi or a phone hotspot is fine (source).
- OBD cable connected from the AutoTuner tool to the car’s OBD-II socket (source).
- Engine running (source), and at normal operating temperature so the runs are comparable.
- A dyno, if at all possible. AutoTuner highly encourages datalogging on a dyno (source). Full-load runs on public roads are dangerous and illegal in most places: use a dyno or a closed, legal track.
Step by step: recording a datalog
- Plug in and start the engine. OBD cable into the OBD-II socket, engine running (source).
- Select the vehicle. Find the car with the ECU selection or the quick search function, then choose the Datalog method (source).
- Wait for the gauges. The software queries the available measures for that ECU from the server; the gauges appear when it is ready. AutoTuner currently displays 12 gauges but records more than 12 values, and all of them are available when you view the log online (source).
- Start the run and record. Start your dyno run and click Record or press the space bar (source).
- Stop. Click Stop or press the space bar again (source).
- Upload. When you stop recording, you can upload the log online to view the graph. To log again, click Record once more (source).

How to make a clean pull
AutoTuner’s recommended run is simple (source):
- Cruise in 3rd gear at about 1,500 to 2,000 rpm.
- Start the log and immediately go to wide-open throttle.
- Stop the log when the rpm reaches the redline shown on the dashboard.
With an automatic gearbox, AutoTuner advises putting the gearbox in sport or manual mode so it does not shift too early or kick down (source).
Our own tips for logs that are useful to compare: log one run on the stock file before the remap if you can, then the same run after; keep the same gear, start rpm and fuel; let the engine and intake temperatures settle between runs; and write down the ambient conditions. One clean pull is worth more than five rushed ones.
Viewing and sharing the log
- My datalogs. All uploaded logs are in the online AutoTuner administration interface under “My datalogs” (source).
- Graph and table. Values appear when you hover over the graph, you choose which measures to display in the right-hand panel, and a table with all the data sits below the graph (source).
- Slave tools. Logs uploaded by a Slave tool are synced automatically to its Master account, so the Master can open them directly (source). More on the Master/Slave split in AutoTuner’s help: help.autotuner.com/en/articles/2984985-what-s-the-difference-between-master-tool-and-slave-tool.
- Sharing. The URL of a log is public, so anyone can open it with or without an AutoTuner account; a “copy link” button under the graph copies it to the clipboard (source). Keep that in mind if the log is linked to a customer’s car.
What to look at after a remap
This is general guidance, not from AutoTuner, and the channels you can check depend on the measures offered for your ECU:
- Requested vs actual boost (and rail pressure on diesels, if logged): actual should follow requested without large overshoot or a gap that keeps growing.
- Load and torque values: they should rise smoothly through the rev range, without sudden drops that point to a limiter or a protection strategy.
- Air/fuel or lambda and exhaust gas temperature, where logged: compare with the stock run rather than chasing a single number.
- Ignition and knock values on petrol engines, where logged: repeated knock retard is a reason to stop and investigate (fuel quality, temperatures, hardware).
- Fault codes after the run, read with your diagnostic tool.
If something looks wrong (flat spot, limp mode, smoke, a fault code), stop testing at full load and talk to whoever made the file.
Send the log to ECU File Market
If your tuned file came from us, reply to your file request with the shared log link and a short note: file version, fuel, ambient conditions, gear used and any symptom. For a new job, upload your original read with the vehicle, engine, ECU hardware and software numbers and the stage you want; credit prices are on our pricing page, and most files are returned in under one hour during support hours. Checksum correction, where needed, is a paid extra. Bench or boot reads also leave a full backup, explained in our AutoTuner backup file guide.
Good practice: only work on vehicles you own or are authorised to work on, keep the original file for the life of the car, and keep all emission control systems fitted and working. This guide does not cover removing or disabling DPF, EGR, SCR/AdBlue or any other emission equipment.
Sources (checked 30 October 2026)
- AutoTuner help: How to datalog with AutoTuner: help.autotuner.com/en/articles/3920632-how-to-datalog-with-autotuner
- AutoTuner, Datalogs flash method and compatibility list: autotuner.com/pages/flash-method/datalogs
- AutoTuner help: Master tool vs Slave tool: help.autotuner.com/en/articles/2984985-what-s-the-difference-between-master-tool-and-slave-tool ; How to export error logs (for support requests): help.autotuner.com/en/articles/2984939-how-to-export-error-logs-file
AutoTuner is a trademark of its owner. ECU File Market is an independent tuning file service and is not affiliated with, endorsed by or sponsored by AutoTuner. The name is used only to describe compatibility and workflow. Use only genuine, licensed tools and software.